Approval of the type of measuring instruments.
It is the same as "entering the SI registry"
In the people - "metrological certificate",
Obsolete name - "type approval certificate"
This procedure involves testing for type approval and obtaining in Rosstandard a certificate of approval of the type of SI.
The procedure for receiving is regulated by the following orders:
Order of the Ministry of Industry and Trade of the Russian Federation of June 25, 2013 No. 970
Order of the Ministry of Industry and Trade of the Russian Federation of November 30, 2009 No. 1081
It is not necessary to read the above documents at all, please call or email us, and we will be happy to inform you all the available information on your specific question!
Well-developed technical documentation for the measuring instrument is a key point for the procedure for approval of the type of SI and certification of equipment. Your products may not be competitive if they do not have the correct documentation. Also, the documentation passes the metrological examination for the correctness of the expression of metrological characteristics and the availability in the technical conditions of the description of methods for their verification. The specialists of our testing center have many years of experience in this matter and will readily take this work upon themselves.
Test equipment - equipment that reproduces normalized external factors and (or) loads.
The procedure for attestation is regulated by GOST R 8.568-97 "GSI. Certification of test equipment. Basic provisions ». The
We offer a full range of services for the certification of test equipment, which includes:
- Metrological examination of technical documentation;
- Development of the program of primary (periodic) attestation;
- Organization and conduct of attestation;
- Registration of the results of certification - protocols and certificate for test equipment.
Orders of the Ministry of Industry and Trade of the Russian Federation No. 970 of June 25, 2013 and No. 1081 of November 30, 2009 regulate the procedure for introducing changes into the type description (annex to the type approval certificate). Changes may affect both metrological characteristics And technical means of measurement. p>
Our testing center will form all the necessary package of documents for metrological examination in order to make changes in the description of the type of measuring instruments and will conduct a set of necessary tests. p>
Usually there are a lot of nuances in this issue that need to be considered, but we always find a solution! p>
Certificate (until 2010 Certificate) type approval of measuring instruments (Metrology Certificate)
This document certifies that the type of the SR approved for compliance with the metrological and technical characteristics specified in the description of the type (obligatory annex to the type approval certificate), and means of measurement made in the State Register of SI.
In the Russian Federation to provide unity in the sphere of state regulation of measuring instruments are special control methods, which are based on compliance with the Federal Law № 102-FZ of June 26, 2008 "On ensuring the unity of measurements" and implemented the relevant supervisory authority by the Federal Agency for Metrology and Technical regulation (Rosstandart).
Rosstandart shall decide on the approval of the type of SI and make it to the state SI register on the basis of positive test results for type approval conducted by an accredited test for this type of testing center (ITs).
How to obtain a certificate of approval of SI?
- Conduct tests for type approval;
- If the results of positive tests to pass the examination documents in the state registry;
- Eliminate gosreesta comments;
- In the absence of comments, get expert opinion and cover letter in Rosstandart;
- Send documentation set, along with a cover letter in Rosstandart;
- Wait for the order of approval of the SI and SI introduction in the state register;
- Pay a state fee for the issuance of a type approval certificate;
- Wait until the certificate is signed by and pick it up from Rosstandart.
If the certificate of approval of the SI type for your measuring instrument ends, it is not necessary to undergo anew the procedure of testing and type approval. p>
According to the order of the Ministry of Industry and Trade of Russia of 25.06.2013, No. 970, you have the right to extend the validity of this certificate for another 5 years. To do this, it is necessary to conduct a mandatory metrological examination of the design and technological documentation of your SI in an accredited testing center (for example, such as ours) and submit a set of documents to Rosstandart no later than 40 working days before the expiration of the certificate. p>